Common Gas Stove Ignition Problems and How to Solve Them

The gas stove is a kitchen essential, but it can be frustrating when you struggle to get the burners lit. You may hear a clicking sound from the igniter, but the flame might not light; or the flame might light briefly, but then go out.

Common Gas Stove Ignition Problems and How to Solve Them

Ignition Failure Issue in Gas Stoves is one of the gas stove problems most commonly encountered. All these problems can ruin your cooking experience and be really irritating. Fixing these basic issues can help save you time and keep your stove operating the way it should.

Lets explore these issues one by one and find effective solutions.

10 Most Common Gas Stove Ignition Problems With Solutions

1. Burner Won’t Light

A person turning on a gas valve

When the igniter is sparking but the burner won’t light, it could be due to a few reasons:

Gas Valve is Closed

  • Problem: The gas valve may be partly closed and gas won’t flow through the valve completely.
  • FIX: Inspect the gas valve and ensure it is on all the way. Rotate the knob or lever in the open position to let the gas completely flow to the burner.

Clogged Burner Ports

  • Problem: The burner ports may become obstructed by food debris or grease.
  • Solution: Using a small brush or a pin, clean out the burner ports to ensure that nothing obstructs the gas flow. Make sure the ports are open to allow the uniform flow of gas.

Non-aligned Igniter

  • Problem: This is when the igniter is not properly aligned with the burner. If it were off, the spark would likely not hit the gas flow.
  • Solution: Position the igniter on top of the burner correctly. These mechanisms allow the spark to combust the gas efficiently.

“Most ignition problems can be avoided with regular maintenance and cleaning. Always make sure the burners and igniters are clear of debris and in the right positions”, says stove technician John Doe.

2. Weak Ignition Spark

A weak spark might not light the burner, following can be potential causes:-

Faulty Spark Module

a person replacing a faulty spark module

  • Problem: The spark module is the part that causes ignition to happen by generating a spark, and must be replaced if it fails. A weak spark will result in a lean mixture which will cause misfiring.
  • Solution: Replace the spark module with a new one. When your oven element burns out, refer to your stove manual or call in a professional to replace the correct broken part. When a spark module is tested properly, it should deliver a powerful, centered spark.

Dirty Igniter

  • Problem: Dirt build-up in the igniter can lower the spark.
  • Solution: Use a soft brush or towel to carefully clean the igniter. Clean as needed to ensure a good spark. Regular cleaning of the igniter and retaining this smoothness will maintain its performance.

Damaged Wiring

  • Problem: Loose or damaged wires can also cause intermittent weak sparks since the electrical connection has been weakened.
  • Solution: Check the wiring for cracks or loose connections. Have damaged wires cleaned or replaced. Keeping all connections tight will keep your spark constant.

3. Continuous Ignition Clicking

A person checking the ignition switch on a gas stove

If your stove keeps clicking, but it is already lit or it fails to ignite, look for these causes:

Stuck Ignition Switch

  • Problem: The ignition switch is probably stuck in the ‘on’ position, which is why there is continuous clicking.
  • Solution: Verify ignition switch is free to move. If stuck, clean or replace to fix the constant clicking. A switch is a safe piece of the machine as it avoids sparking.

Moisture in Igniter

  • Problem: When there is moisture in the igniter, it can interfere with the electrical components and cause the igniter to keep clicking.
  • Solution: If the igniter has gotten wet, dry with a dry cloth, or use a low-setting hairdryer to dry completely. Make sure the igniter area is dry. If the starter plate is kept dry in this way, it will not click continuously.

Defective Spark Module

  • Problem: This chip is the cause of some continuous clicking noises (if the module has gone bad, it can start to click even when not needed).
  • Resolution: Replace the spark module. Check your owner’s manual, or if you are not sure how, consult with a professional technician for the right replacement.

Source: REEN Family Journal – How To Fix A Gas Stove Igniter That Won’t Stop Clicking

4. Ignition Delay

A person cleaning clogged burner ports with a pin and other checking gas supply

Many reasons can cause ignition delay and most common of them are below:

Clogged Burner Ports

  • Problem: Food particles or oil can clog the burner ports and hinder the flow of gas.
  • Solution: Clean the burner ports with a small brush or a pin to clear them of any debris. Make sure the ports are not clogged and allow an equal amount of gas to flow through them.

Read more about “how to clean gas stove burners“.

Low Gas Pressure

  • Problem: If the gas pressure is low, the ignition will take time.
  • Solution: Check the gas supply line for any bends or blockages. If the pressure is still low, get in touch with your gas provider and make sure there’s no trouble with the gas supply.

Dirty Igniter

  • Problem: A dirty igniter doesn’t produce a good spark.
  • Solution: Use a soft brush or a cloth to clean the igniter. A little gentle scrubbing will remove any built up dirt and produce a good spark which will light up the stove in no time.

5. Igniter Not Functioning

If the igniter is totally not functioning, consider the following reasons:

Power Supply Issue

A person checking the power plug of a gas stove

  • Problem: The igniter is not getting power.
  • Solution: Make sure the stove is properly plugged in and the power supply is ok. Check the circuit breaker to see if it hasn’t tripped. If the stove is plugged in and the power is good but the igniter is still not working then the problem lies within the stove.

Faulty Ignition Module

  • Problem: The ignition module has gone bad.
  • Solution: Replace the ignition module. Check your stove’s manual or contact an authorized technician to replace it with the correct one. A good ignition module will ensure the igniter functions properly.

Broken Igniter

  • Problem: Your igniter may be broken.
  • Solution: Check the igniter for any physical defects. If you find that it’s broken, you will need to replace it with a new one. The igniter plays a huge role in the overall function of the stove and you will not be able to use it properly unless this component is in working order.

6. The burner ignites but goes out quickly.

A person replacing a defective thermocouple in a gas stove, alongside another stabilizing a pilot flame

When the burner ignites but will not remain lit, it may be a result of:

Defective Thermocouple

  • Problem: The thermocouple can sense whether the pilot light is on and can cut off gas flow in case it is not.
  • Solution: Replace the thermocouple. A correctly operating thermocouple is supposed to ensure that the burner remains on for the duration it is supposed to.

Unsettled Pilot Flame

  • Problem: An unsteady pilot flame can result in the burner being blown out.
  • Solution: Clean the pilot orifice and stabilize the flame. A stable pilot flame is vital for good burner operation.

Gas Supply Issues

  • Problem: An irregular gas supply causes the burner to go out.
  • Solution: Ensure the gas supply line is not kinked and there are no leaks. Check that the pressure and flow of gas are adequate and consistent. If the problem continues, contact your gas supplier.

7. Intermittent Ignition

A number of reasons can cause ignition inconsistency:

A person tightening electrical connections and  another checking a gas regulator for proper operation

Loose Connections

  • Problem: Loose electrical connections within the igniter can cause trouble with the proper function.
  • Solution: Always ensure all the electrical connections are secure. Tighten any poor electrical joints or connections to reestablish the spark.

Gas Supply Variation

  • Problem: Gas pressure variations can cause intermittent ignition.
  • Solution: Check the gas supply line for kinks or blockages and check for proper regulator operation. If this does not eliminate the problem, please get in touch with your gas supplier.

Faulty Control Knobs

  • Problem: The control knobs are faulty because they may interfere with the supply of gas to the burner.
  • Solution: Replace all defective control knobs to ensure functionality and a reliable ignition system.

8. Pilot Light Issues

A person relighting the pilot light of a gas stove alongside another cleaning the pilot orifice

If the pilot light is continuously going out, try these solutions:

Pilot Light Outage

Issue: A pilot that goes out can interrupt proper stove operation.

Solution: Relight the pilot light according to your stove’s instructions in the manual. Refer to our blog on how to fix a pilot on Gas Stove;- https://stovemastery.com/how-to-fix-a-pilot-light-on-a-gas-stove/

Blocked Pilot Orifice

  • Issue: Flame blocked by dirt or other foreign material in the pilot orifice.
  • Solution: Clean the pilot orifice with a needle or compressed air so that the flame passageway is clear.

Faulty Thermocouple

  • Problem: There is a risk that the pilot flame may fail to be detected by the thermocouple.
  • Solution: Replace the defective thermocouple. The thermocouple is a part that serves to keep the pilot flame alive, and it remains on by controlling the gas flow.

9. Short Circuits in the Ignition System

Short circuits may be caused by:-

Exposed Wires

  • Problem: Exposed wires can cause short circuits and igniters that work improperly.
  • Solution: Inspect wiring for damage or wear and protect bared wires with electrical tape or replace wiring.

Water Damage

  • Problem: Moisture causes electrical faults in the ignition system.
  • Solution: Dry out the wet areas and replace damaged parts. Then, in the future, exposure of the equipment to such conditions should be avoided to save the system.

System Electrical Faults

  • Problem: Faulty electrical parts are a scourge to the ignition process.
  • Solution: Replace any defective electrical components. The proper function of the electrical system is key for ignition to be reliable.

10. Poor Burner Flame

A person cleaning the clogged burner cap of a gas stove, alongside another adjusting the gas regulator settings

An uneven or weak flame can be due to following potential reasons:

Clogged Burner Cap

  • Problem: Contaminants held in the burner cap can restrict the gas flow.
  • Solution: Clean the burner cap thoroughly to ensure a uniform flame.

Incorrect Gas Regulator Settings

  • Problem: Incorrect gas pressure will result in the wrong flame.
  • Solution: Reset the gas regulator by the instruction from the stove’s manufacturer. Call an expert if needed.

Defective Burner Head

  • Problem: The burner head has a problem, resulting in an uneven flame.
  • Solution: The replacement of the burner head is defective and should be done to have good work.

FAQs on Common Gas Stove Ignition Problems

Why does my gas stove igniter click but not light the burner?

This usually happens due to a closed gas valve, clogged burner ports, or a misaligned igniter. Check these components and clean or align them to ensure their good condition.

What can I do if my gas stove igniter continues to click repeatedly?

Continuous clicking can be caused by an ignition switch stuck open, moisture around an igniter, or a defective spark module. Dry the igniter area, check for switches that may have become stuck, and consider replacing the spark module if necessary.

How do I fix this intermittent problem with the gas stove not lighting?

A loose connection, fluctuating gas supply, or a defect somewhere in the control knobs could create intermittent ignition. Secure all connections, check if the gas is constant, and check the control knobs.

Why does my gas burner on the gas range ignite but go almost out quickly?

This problem may be due to a failed thermocouple, unstable pilot flame, or gas supply problems. Check the thermocouple and the pilot flame, and make sure the gas supply is stable and sufficient.

How can I correct the low burner flame on my gas range?

If the flame is poor, there may be a burner cap that is blocked, wrong settings of the gas regulator, or possibly the burner head being faulty. Clean the burner cap, correct the gas regulator settings, and, in the case of a defective burner head, replace it.

Conclusion

Knowing gas stove ignition problems and being able to handle them makes your cooking experience wonderful. We have addressed nearly all typical problems encountered with stove ignition systems and provided practical solutions for each one.

By knowing these problems you can make sure that your stove lights and operates efficiently. Keep your stove at high operational efficiency, keep it clean, maintain it, and do all repairs in good time.

Call a professional immediately if you have consistent problems before things get out of hand.

Leave a Comment

Do you have any custom Problems?

Ask us any questions

Get in touch